Questions, answered.

Santim SC-1 est une interface CAN pour véhicules. Elle prend en charge tous les véhicules CAN classique et CAN FD du marché, et lorsqu’un nouveau véhicule est lancé, il est compatible immédiatement. Pas d’attente, pas de demande.

SC-1 connects to the vehicle’s CAN network and provides the system it serves with the vehicle data it needs. It is installed by authorised Santim service partners and set up with the SConnect app.

Les interfaces classiques prennent en charge les véhicules à partir d’une liste, et les nouveaux modèles attendent une mise à jour. SC-1 prend en charge le CAN classique et le CAN FD : un nouveau modèle est donc compatible dès le lancement.

POWER (green) shows that supply is present, CAN (yellow) shows CAN activity and ERROR (red) indicates a fault. The installation guide has the full LED reference and troubleshooting.

Over Bluetooth Low Energy to the SConnect app, and through its USB-C port. Earlier hardware revisions use micro-USB.

SC-1 operates from −40 … +85 °C and is rated IP40. Install it in a dry place inside the cabin.

Les véhicules équipés d’un réseau CAN classique ou CAN FD : voitures particulières, véhicules utilitaires légers, taxis, bus, camions, véhicules électriques et hybrides, véhicules spéciaux et machines agricoles.

Il est compatible dès le lancement. La prise en charge dépend du réseau du véhicule, pas d’une liste de modèles.

Non. Si le véhicule utilise le CAN classique ou le CAN FD, SC-1 le prend en charge.

Yes. Electric and hybrid vehicles run on classic CAN and, on many newer platforms, CAN FD. SC-1 supports both. During installation and the road test, the vehicle must be in READY mode.

Yes, whenever the vehicle network is classic CAN or CAN FD, including networks that use 29-bit identifiers.

Most vehicles built from the mid-2000s onwards use CAN. If an older vehicle has a classic CAN network, SC-1 supports it. Contact us and we will confirm it with you.

Classic CAN carries up to 8 data bytes per frame at a single bitrate. CAN FD (flexible data-rate) carries up to 64 bytes and can switch to a faster bitrate for the data phase. Newer vehicle platforms increasingly use CAN FD, and SC-1 supports both.

Nominal bitrates of 83,3 kbit/s, 125 kbit/s, 250 kbit/s, 500 kbit/s et 1 Mbit/s.

Yes. SC-1 supports CAN 2.0A frames with 11-bit identifiers and CAN 2.0B frames with 29-bit extended identifiers.

High-speed CAN to ISO 11898-2, the physical layer of the classic CAN and CAN FD networks in today’s vehicles.

SC-1 is installed by authorised Santim service partners, using the SConnect app and the installation guide.

In a dry place inside the cabin, away from heat sources, moving parts and airbag deployment zones, with the LEDs visible for service. SC-1 is rated IP40.

Constant +30 through a fuse of no more than 2 A, switched +15, ground, and the CAN-H and CAN-L wires of the vehicle’s twisted CAN pair.

No. Never cut or extend the vehicle’s CAN wires. Tap the twisted pair in place through a short window of insulation, solder with an EMC-safe iron or use approved connectors, and insulate every joint.

SC-1 runs on 7,5–32 V DC, so it suits 12 V and 24 V vehicle systems. It draws < 80 mA in normal operation, and in sleep mode < 2 mA at 12 V and < 1,5 mA at 24 V.

With a short road test, all four wheels on the ground, following the prompts in SConnect. A lift or a roller test bench cannot replace the road test.

Check the fuse, measure the supply at SC-1 (it should be within 7,5–32 V DC), check +15 with the ignition on and confirm a solid ground. The installation guide has the full troubleshooting tree.

SConnect is Santim’s professional app for authorised Santim service partners. It pairs with SC-1 over Bluetooth, shows the device status and guides the installation from start to finish.

SConnect is built for Android and iOS. The Android version is available on Google Play.

SConnect is made for authorised Santim service partners. Contact us to become a partner or to get access for your team.

Yes. Pairing, the device status and the final setup steps all run in SConnect.

Contact our sales team. We will talk through your vehicles, volumes and installation plans and prepare an offer for your project.

Yes. SC-1 is installed by authorised Santim service partners. If you run a workshop or an installation business, contact us about becoming a partner.

Start with the installation guide and its troubleshooting tree. For anything else, contact Santim directly: our team supports partners with installation and technical questions.

Santim runs regional sites for Switzerland, Italy, Austria and France alongside santim.tr. Contact us about availability in your country.

Santim Technologies, a technology company built on more than 25 years of automotive electronics experience.